Contact Info

Telephone:
(86 20) 34809599 ext. 6227

Fax:
(86 20)84664738

Email:
Plastic machinery:
monica.lee@jasu-cnc.com
jody.peng@jasu-cnc.com
Email:
CNC:
jody.peng@jasu-cnc.com
  • Contact Suppliermonica.leeContact us
    Contact SupplierJody.PengContact us
    Contact SupplierhildaContact us Contact Supplier

JASU PET blowing machine approved according to CE certificates

Skype Contact Supplier Chat now
QQ Contact us Contact us
Telephone 0086-13928775780
Fax 0086-34806057
Contact Supplier

Product Description

JASU PET blowing machine approved according to CE certificates

High performance 
High effective 
High energy saving

Along with the increasing requirement to high quality and outlook appearance, the products manufactured by the old style extrusion blowing  machine cannot fulfill the customer demand any further. The whole process including mould injection, stretch blowing and off-molding can be finished within one step if using PET blowing machine for manufacturing. The products from this machine don't contain any flash, sprue, and much less disfigurement. It can present the perfect looking mouth, bottom and wedding line as well as the better transparence and higher rigidity. PET blowing machine products are thinner than old style ones, which can save 50% material. Besides the merit mentioned above, the one step injection blowing moulding machine can perform the higher speed and more efficient energy saving.

Typical Products for Injection Blow Molding

JARS – These are made in PP, HDPE, PS, MIPS, SAN etc. Jars are made in a wide variety of materials. The process advantage is that no secondary trimming (scrap) is required when making the neck finish. Ovaloid neck (petroleum jelly) jars can be made by injection molding the neck finish.
.........................................................................................................................................................................
ONE PIECE ROLL-ON DEODORANTS in PP and HDPE. Close tolerance of the injection moulded ball seating allows an even application of the deodorant product. Snap-on ball housings are also used on SAN and PET bottles used for clarity.
.........................................................................................................................................................................
DROPPER BOTTLES – Usually produced in virgin PET. JASU IBM machines are installed in clean manufacturing environments worldwide. The bottles can be stripped from the core rods whilst still very hot and transported to the clean room in sterile air for packing.
.........................................................................................................................................................................
TABLET and PILL BOTTLES(Pharmacy Bottle) – These are made from PP, HDPE, LDPE and PS. These bottles can be designed with complicated injected neck finishes for Child Resistance or pilfer-proofing. Also the neck finish is excellent for barrier seals against moisture with a plug seal closure, and also very flat for tamper foil application.
.........................................................................................................................................................................
Sport bottles(Space bottles) – These bottles are mainly made in PC. Up to 4 cavity molds from 15-20 second cycles. QUALITY PRODUCTS do not cause problems on decoration, filling or capping lines, and are less liable to bring customer complaint.
.........................................................................................................................................................................
LED Lampshade – PC/PET lamp cover for energy saving light

Products Photos:

Injection Blow Molding machine

Injection Blow Molding machine

Injection Blow Molding machine

Injection Blow Molding machine

Injection Blow Molding machine

Injection Blow Molding machine

Injection Blow Molding machine


JASU injection blow molding machine advantages:

1.Electrical motor and pneumatic drive, avoid hydraulic dirty product.
2.Full automatic control, easy operation.
3.Material barrel and hot runner temperature control accurately.
4.Save more cost than traditional machine.
5.Compact structure.
6. Injection: 
     Hot runner and temperature control device and standard configuration
     Only change mold to make a new product. 
     Blow: 
     Hydraulic mold clamping, core insert, blow and bottom molding are standard
     configuration.
     Product release: ejector is a standard device.

Compare Injection Blow Molding to Extrusion Blow Molding

Injection Blow Moulding

Extrusion Blow Molding

No scrap

20-40% scrap during production

Uniform wall thickness

Wall thickness variation

Bottle weight variation of 1%

Bottle weight variation of 3%

Slower cycle time / more cavities

Fast cycle time / less cavities

Thin walls difficult to control

Thick & thin wall capabilities

Hollow Handleware not possible

Hollow Handleware

Necks made with injection molded tolerances

Necks made with blow molded tolerances

One technician per 4-6 machines

One technician per 1-2 machines

Process  is controlled and repeatable with no adjustments

Variable process requiring constant adjustment

Almost no ancillary equipment

Lots of ancillary equipment needed

S/NItemParameter
ISB 800A-3
1Injection PartScrew Diameter50mm
2Screw L/D Ratio20.5:1
3Screw Speed0-150r/min
4Theoretical Injection Capacity481cm³
5Injection Pressure176Mpa
6Max. Hydraulic Pressure140Kg/cm
7The Actual Injection Quantity452g
816Oz
9Screw Stroke245mm
10Clamping PartBlow Clamping Force80Kn
11Clamp Tonnage600Kn
12Wheel Diameter800mm
13Max. Height of Bottle230mm
14Open Vertical Mode Trip430mm
15OtherMax. Pump Pressure16Mpa
16Motor18.5Kw
17Electric Power12.2Kw
18Tank Volume400L
19Dimension4.1X1.45X3.1m
20Weight6Ton


                   

Email to this supplier

Contact Us